Search over 1400 essential trade products. Find it. Fix it. Finish it.

Order before 3.30 for next day delivery.




REF: AD02LP61.5

With a unique formula, TensorGrip LP61 Sprayable contact adhesive is designed for permanent and lifetime bond of materials where a high grab and super... Read More

£10.92 ex vat


Availability: In Stock
£10.92 ex vat


total: £0.00 +vat

Order before 3.30 for guaranteed next day delivery

With a unique formula, TensorGrip LP61 Sprayable contact adhesive is designed for permanent and lifetime bond of materials where a high grab and superior bond strengths are required. Suitable for bonding most laminates, veneers and other decorative surfaces.

Ideal for use in critical situations, TensorGrip LP61 is non- flammable and is the first canister spray contact on the market to be awarded a Class O fire rating.

Available in:

  •  500ml Aerosol


Tensorgrip LP61 is High performance contact adhesive suitable for bonding HPL and to worktop edges and a variety of substrates including MDF, chipboard, plywood and many other timber sheet materials. Tensorgrip LP61 is designed for permanent bonding of materials where immediate bond strength and high heat resistance are required. Tensorgrip LP61 can also be used for bonding sheet metals, where surface preparation is very important - surface must be degreased and lightly abraded with fine abrasive or non-woven material.

Always test Tensorgrip LP61 to determine suitability for your particular application prior to use production.

Not recommended for use with plasticised vinyl's flexible plastics, expanded/extruded polystyrene, PE or PP.

Material Safety Data Sheets and Technical Data Sheets must be read and understood before use. 


Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc. For best results the temperature of the adhesive and the surfaces being bonded should be between 16°C - 27°C

When possible we recommend shaking the aerosol well before using. 


Prior to use check compatibility by spraying a small test patch of the adhesive on the substrate. This product may degrade some substrates.

Spray about 10-20cm away at a 90° angle to the surface applying a uniform even coat of adhesive to obtain 80% to 100% coverage of the surface. If necessary spray another coat of adhesive in areas that appear to need more adhesive. Spray both surfaces to be bonded, one surface vertically and the other surface horizontally. Allow the adhesive to tack off until no adhesive transfer to the knuckle when touched.

Adhere surfaces and press together with adequate pressure. A roller is recommended to apply a uniform pressure to achieve maximum strength. Allow 24 hours for the adhesive to fully cure.


Canister Storage/Change Over

Turn valve on canister into the off position, spray out remaining adhesive left in the hose, disconnect the spray hose and gun from the canister. Reconnect the spray hose to a canister of solvent (sold separately) and spray out until liquid is clear which indicates that the hose and gun is clean. If you choose to leave the hose and spray gun on the canister leave the valve on the canister open. Do not disconnect the hose/gun from the canister. Close and lock the spray gun. 


For removing excess glue use Tensorgrip C101.


Shelf life: 18 months from date of manufacture. 

Do not store at temperatures over 50°C. For optimum performance store at 18°C during use but must always be above 10°C

Avoid exposure to direct sunlight. Do not store directly on concrete floor.

When connected keep valve open and hose pressurised at all times. Do not close valve until ready to connect to new cylinder. 


  • Use only in well ventilated areas
  • Do not thin or reactivate with solvents
  • Do not incinerate
  • Do not expose to extreme heat over 50°C
  • Keep away from sources of ignition
  • Release pressure before disconnecting hose
  • Test for suitability before use


Sign up for offers
straight to your inbox.